2012年9月27日星期四

Outdoor wood-plastic composite floor


China has the world's largest construction market, and the unit energy consumption of building area of 2 to 3 times the developed countries, building energy consumption accounts for 27% of the energy consumption of the whole society, wall materials and doors and windows are the main factors affecting the building energy efficiencyone. Liao, president of the China Plastics Processing Industry Association, said that the potential applications plastic building energy efficiency market in China, not only a large number of on behalf of the steel, and wood, but also has energy-saving materials, ecological protection, improving the living environment to improve the function and quality of construction. reduce building weight, convenient construction superiority. He explained that the Ministry of Housing and Urban building energy efficiency overall objective: to 2010 new construction in cities and towns throughout the country to achieve 50% energy saving. Provide reliable quality, excellent performance of the new plastic wall materials and energy-saving windows and doors for energy-efficient buildings, both the burden shouldered by the plastics industry, but also provides a huge space for the development of the industry. Wood plastic composite extrusion equipment
Polyurethane (PU) rigid foam is recognized worldwide as the best insulation materials, construction is simple and cost-effective. Studies have shown that building every 1 kilogram of polyurethane material, equivalent to a decrease of 755 kg of CO2 emissions in the average life of.
It is understood that the PU rigid foams for thermal insulation performance is superior, the lowest thermal conductivity of organic and inorganic insulation materials, and excellent mechanical properties, can withstand a wide temperature range and high-humidity conditions of wind, impact a variety of loads. The material also has a certain toughness, not easy to produce cracking; excellent waterproof, separated steam performance, it is difficult to compare to other insulation materials. PU rigid foam as well as from the carbonization of self-extinguishing characteristics, which can reduce the rate of spread of flame. At present, the building insulation materials in Europe and the United States and other developed countries, about 49% of the polyurethane material, but the proportion in China is still less than 10%. To this end, Liao said, enterprises should actively research and development of low smoke, low toxicity flame retardant green polyurethane foam material, to win market opportunities.
Can be made of polystyrene foam (EPS), the continuous extruded polystyrene foam (XPS) insulation performance, as technically ripe for energy-saving building materials, mainly used in the construction of walls, roof,places such as windows, doors and ground. EPS, XPS foamed magnification up to 50 times, EPS98% of the volume of air, only 2% of the material, is a fixed air, shock, saving resources, excellent material, with an average load 5 tons per square meter. In addition, microporous plastic with excellent performance, fatigue life increased by 4-7 times 6-7 times higher impact strength than traditional insulation materials, to speed up the process of industrialization will be a major breakthrough in energy efficiency (insulation, thermal insulation) materials.
According to the the WPC Professional Committee of CPPIA vice president, chairman of Beijing of Futuresoft Technology Development Co., Ltd., Dr. Song Weining, phenolic foam in recent years developed a new type of material, its flame resistance, low smoke and high temperature stable performance, the adiabatic insulation, sound insulation, easy molding, better durability, and is known as the third generation of emerging insulation materials. In the next few years, phenolic foam, the output value will be the average annual growth rate of 20%. Outdoor wood-plastic composite floor
China is the world's first large windows and doors production and user countries, doors and windows of the demand growth rate of 11% per annum in the doors and windows of the annual new housing demand of more than 500 million m2, while the existing building renovation demand for energy-saving windows and doorsover one billion square meters, Fenestration annual total consumption is equivalent to four times that of Europe.
It is understood that the plastic doors and windows, energy efficiency is very prominent, with insulation, sound insulation and moisture characteristics. In the heat transfer, the thermal conductivity of plastics only steel 1/360, 1/1250 of the aluminum, has good insulation properties. At the same time, the plastic doors and windows profiles are multi-chamber structure, make full use of the thermal insulation properties of air, and further reduce the thermal conductivity of the material as a whole. In airtight performance, the plastic door sash feed or fan material between by melt welding, window frames, sashes are a whole, there is no gap between the horizontal and vertical material eliminate the air through the corner of the cross feed and vertical feed stitching possibilities.
According to information available, the plastic profile manufacturing has great advantages in energy saving, from raw materials to produce the whole process of the product point of view, the production of one ton of plastic profile than the production of one ton of aluminum saving 10,000 kwh left and right, and more to produce 1 ton of plastic profile can save 3.6 tons of coal, to reduce the CO2 emissions of 9.43 tons, 30.6 kg to reduce the emission of sulfur dioxide gas, to reduce the emission of nitrogen oxide gases 26.64 kg. best outdoor wood plastic floor

2012年9月26日星期三

WPC is indeed vast not sporting running

best outdoor wood plastic door, wpc flooring

wpc flooring can be fairly also excellent for children
Presently, plenty of the youthful era are fond of developing their residences by signifies of their own personal palms and wrists. Nevertheless, they're now able to fashion and design their specific design and style and have the super fruit on the occupation.

In conditions of your decotative components, allow us just about all give considered to timber, stainless metal and most numerous other modern as properly as higher-tech things. Nowadays, any solid wood plastic composite information is fairly nicely acknowledged as it is not simply especially environmental, but most likely specifically price-efficient. Also, these toppers is truly excellent, so you can conserve a great deal of money as it would be and so hard-putting on.


Normally, wpc flooring can be very also wonderful for youngsters. The purpose getting this kind of floor is incredibly breathtaking like length, it can surely communicate your user's individual flavor. Thinking about that the wpc flooring provides in depth characteristics, it truly is mainly recognised from the majority youthful folks across the entire world. This content material will be moistureproof, bacteriostasis and then mothproof, therefore it is presently conventional identified in design and style sector. In addition, shoppers can protect environmental environment employing this content. Featuring bonus, all the wood plastic substance blend will get much more and much more well-liked someday soon.

WPC the sort of entirely new info in buy to adjust solid wood material. It is usually in other phrases model-new composite resin material in synthesizing plant linens and plastic supplies, now WPC might be see 1000's its personal matters with each other with the attributes of plant nutritional fibre and encompasses. As a consequence of these particular constructive facets, the software of WPC is indeed vast not sporting running footwear virtually characteristics all of the positioned spheres, just like wood, naff, steel, metallic and distinct farms. For the time being, WPC even handles the particular try to recycle predicament with naff and solid wood waste materials remedies.

WPC can be used for item packaging neighborhood. Acquiring trays like, whitening tray content material on Us room is frequently fantastic while 190 , 000, 000, at the identical time WPC trays account for share of discuss of the market. As for each the records by way of JRP, Malay people must get gain of with regards to 6 million associated with teeth whitening trays each and every 12 months, and WPC containers are the lead to of 80% connected with industry reveal. From your globally thoughts-established, WPC tooth whitening trays are enduring additional and much more human beings completely adore, WPC containers will definitely switch containers which you'll discover built from other materials in the future.

Author Name: Outdoor wood plastic floor

Author Bio:
WPC the kind of completely new information in order to change wood substance. It is usually in other words brand-new composite resin content in synthesizing plant linens and plastic materials, now WPC might be see thousands its own matters together with the attributes of plant dietary fibre and covers. Wood plastic composite extrusion equipment
Wood plastic composite flooring
best outdoor wood plastic door
wpc flooring can be fairly also excellent for children
Presently, plenty of the youthful era are fond of developing their residences by signifies of their own personal palms and wrists. Nevertheless, they're now able to fashion and design their specific design and style and have the super fruit on the occupation.

In conditions of your decotative components, allow us just about all give considered to timber, stainless metal and most numerous other modern as properly as higher-tech things. Nowadays, any solid wood plastic composite information is fairly nicely acknowledged as it is not simply especially environmental, but most likely specifically price-efficient. Also, these toppers is truly excellent, so you can conserve a great deal of money as it would be and so hard-putting on.


Normally, wpc flooring can be very also wonderful for youngsters. The purpose getting this kind of floor is incredibly breathtaking like length, it can surely communicate your user's individual flavor. Thinking about that the wpc flooring provides in depth characteristics, it truly is mainly recognised from the majority youthful folks across the entire world. This content material will be moistureproof, bacteriostasis and then mothproof, therefore it is presently conventional identified in design and style sector. In addition, shoppers can protect environmental environment employing this content. Featuring bonus, all the wood plastic substance blend will get much more and much more well-liked someday soon.

WPC the sort of entirely new info in buy to adjust solid wood material. It is usually in other phrases model-new composite resin material in synthesizing plant linens and plastic supplies, now WPC might be see 1000's its personal matters with each other with the attributes of plant nutritional fibre and encompasses. As a consequence of these particular constructive facets, the software of WPC is indeed vast not sporting running footwear virtually characteristics all of the positioned spheres, just like wood, naff, steel, metallic and distinct farms. For the time being, WPC even handles the particular try to recycle predicament with naff and solid wood waste materials remedies.

WPC can be used for item packaging neighborhood. Acquiring trays like, whitening tray content material on Us room is frequently fantastic while 190 , 000, 000, at the identical time WPC trays account for share of discuss of the market. As for each the records by way of JRP, Malay people must get gain of with regards to 6 million associated with teeth whitening trays each and every 12 months, and WPC containers are the lead to of 80% connected with industry reveal. From your globally thoughts-established, WPC tooth whitening trays are enduring additional and much more human beings completely adore, WPC containers will definitely switch containers which you'll discover built from other materials in the future.
Wood plastic composite extrusion equipment
Wood plastic composite flooring

best outdoor wood plastic door

Wood plastic composite extrusion equipment


Wood-plastic composite material is restricted due to density, high cost, brittleness, toughness, and wood substitutes in some industrial areas as applications. PVC wood—plastic hollow door board production line
In recent years, by adding a foaming agent in wood-plastic composites, wood-plastic composite materials forming microporous can passivation of the crack tip to prevent crack propagation, can effectively control the lack of wood-plastic composite materials, making plastic foam The material has been applied in automotive interiors, aerospace, and decorating. Wood-plastic composite foam molding compression molding, extrusion and injection molding, is a new area of ​​research.
Wood-plastic composite materials also need to protect the wood-plastic composite material applications as outdoor wood substitutes most fundamental advantages is its low maintenance and weather resistance. But be sure to pay attention to are: low maintenance is not maintenance-free. Need for the protection of WPC appearance ADD weatherability of the pigment and the UV stabilizer to reduce fading. Some manufacturers to adopt the way of co-extruded wood-plastic composite materials coated with a layer of plastic off the timber and environmental isolation, reduce moisture and strain of the wood, and only using high levels of additives in the surface layer. Wood plastic composite extrusion equipment
Waste plastics and waste wood wood-plastic composite material can be used as a raw material itself can be recycled, and therefore has a good social effect in terms of resources and environmental protection, has been widely used in the construction, transport, automotive and other industries. The attention of the global processing industry of wood-plastic composite materials is increasing in Western countries has shown a rapid growth momentum. Worldwide, the growing interest in environmentally friendly materials, the industry needs a positive response to the demand for this market, to meet the challenge, the urgent need of a reliable, profitable and cost-effective technologies continue to emerge. WPC will cause increasingly widespread attention as an outstanding application of an economic, ecological alternatives. wood plastic composite for extrusion line
Wood-plastic composite material is a new type of green building materials, surface appearance, good performance, workmanship, form complex, has a huge market for building materials such as doors and windows, decorative, pinch, template, curtain wall application. Wood plastic aluminum composite windows and doors insulation coefficient over the thermal insulation requirements of the building windows and doors for Beijing, Tianjin, and therefore can play an important role in building energy saving.
Wood-plastic composite insulation performance is significantly better than the insulation broken aluminum can avoid indoor condensation of aluminum windows and doors is difficult to solve the leakage problem; whole window wind pressure, water tightness, air tightness performance than steel doors and windowsand avoid deformation window; weather and the useful life than steel doors and windows. In addition, wood surfaces can be processed into solid wood, metal, marble and other effects, decorative aluminum and steel doors and windows. Production of wood-plastic products can be used more than 98% recycled materials, and can be 100% recycled, waterproof, does not rot, anti-moth-eaten, salt, acid, maintenance-free, free paint, formaldehyde and other characteristics, and therefore in the building materials field meteoric rise, promotion and development in China. In his view, energy saving and environmental protection, the development prospects of the wood-plastic composite materials can be expected. wood plastic composite extrusion processing

2012年9月18日星期二

all kind of composite material


Our factory wood-plastic composite building decoration parts Development Strategies

1. Adjustment of product structure

Around the construction administrative departments and relevant departments from the product structure adjustment, limit and eliminate backward technology, the energy consumption of the product, to actively encourage and support the development of wood-plastic composite building decoration parts. For new construction, renovation of multi-storey buildings should promote the use of wood-plastic doors and windows, wood floors and wood-plastic decorative plate. all kind of composite material

2. To determine the focus of scientific and technological development

Actively absorbing foreign advanced technology. Strive to the end of the century. So that the full range of the main products of wood-plastic composite building decoration parts and raw materials. Parts supporting. The overall level of the developed countries, the level of the nineties. According to the needs of the market at the same time, great efforts to develop new varieties.
(1) the raw materials and auxiliary materials (including various additives, stabilizers, adhesive, etc.). Should be based on the performance of wood-plastic composite building decoration parts processing requirements. Development of special materials, in order to protect the processing performance and quality of the products. cheapest composite fencing
(2) take the introduction, digestion and absorption and self-development combined road and improve wood-plastic wood-plastic composite building decoration parts processing equipment and mold manufacturing level, raise the the mechatronics level of domestic wood-plastic composite building decoration parts host device, manufacturing precision, reliability and ergonomics than at the same time, focusing on the ancillary equipment research and development, and improve the overall level of the production line.
(3) strengthening components supporting the development and the formation of large-scale production, focuses on the development of interior window cover and skirting, to establish the corresponding parts of industrial production base.
(4) to strengthen the research of wood-plastic composite building decoration the parts engineering applications technology. Summary of wood-plastic composite building decorative parts design and construction of the pilot project in a timely manner, the preparation or amendments to the technical regulations, the standard pattern and project budget fixed, to guide the application of wood-plastic composite building decoration parts in the project.

3. Improve the quality of management measures to regulate the sales market.

(1) wood-plastic composite building decoration parts production enterprises in accordance with the requirements of ISO9000, establish and improve the corporate quality assurance system and after-sales service seeking promise to provide quality products for construction projects. best composite material suppliers
(2) to organize the national decorative parts of the wood-plastic composite building technical level assessment bulletin and push the floating quality products. Exposure inferior products.
(3) over the relevant departments to strengthen the quality supervision and inspection of wood-plastic composite building decorative parts. The actual local situation to establish product promotion, identification, demonstration system.
4. Timely development and revision of the standard specification.
5. Development of relevant technical and economic policies, such as: the application of new products, the economic benefits of the new technology and support policies, eliminated the traditional high energy consumption and product use of the environment caused by the impact of building decoration materials products technology policy. best material for wood flower boxes

Wood-plastic composite building decorative


Wood-plastic composite building decorative parts in the WPC profile or plate as the main material, through modern parts factory production mode, production of a variety of architectural decoration parts. North America is the largest regional building the world's wood-plastic composite decorative parts market. Wood-plastic composite building decoration parts in addition to be used as decking, wainscoting, ceilings, decorative panels, running boards, siding. In addition, it can also be used for decorative borders, fences and garden handrails. best composite decking ratings
Wood-plastic doors and windows with good insulation, energy-saving, sound insulation, fire-retardant, anti-corrosion, anti-aging, impact resistance, no deformation, beautiful and elegant luxury features. Currently, in the United States and European countries have been widely used each year in the United States a total amount of 30 million sets of doors and windows, doors and windows Institute, which accounted for 48% of plastic doors and windows, accounted for 31% of wood-plastic composite windows and doors.
Promotion and application of the wood-plastic composite building decorative parts of the domestic factory is still in its infancy, most dependent on foreign high-priced imports. At present, the domestic production of wood-plastic composite building decoration parts mainly in this area of ​​the building interior doors, the other hand, the production the the WPC profile of natural materials in thermoplastic materials are mostly stop at as filler in the domestic and foreign enterprises wood flour. plastic fasteners australia
"Bundchen brand wood-plastic composite interior doors for Environmental Science and Technology Co., Ltd. of Fujian Furi production profiles based on natural plant long fiber and senior precious wood flour mixed hybrid modified the filled PVC resin, the comparable single wood flour filled thermoplastic has more The strong mechanical reinforcement role, but also lower cost. In the 11th Five-Year period, China is clearly building a resource-saving and environment-friendly society, advocating vigorously promote energy-saving environmental protection, new building materials, adhere to the circular economy, green buildings, conserve resources and protect the environment, to achieve social and environmental benefits and economic benefits of the organic unity of the architectural decoration. And adhere to replace backward production methods, advanced production and parts production factory and on-site construction assembly of architectural decoration industry to gradually make a new road to industrialization. Therefore, the factory wood-plastic composite building decoration parts, has broad application prospects in the domestic and foreign markets.
Our factory wood-plastic composite building decoration parts, the existing problems in the actual promotion process:
1. Scientific propaganda is not enough wood-plastic composite construction the decorative parts environmental protection and energy saving, long life, convenient construction, low cost of project characteristics, there is still a lot of people do not understand.
2. the standard specification serious lag. Currently, in our country have not worked out the wood-plastic composite building decoration parts national standards, design, construction specifications. best composite lumber suppliers
3. Engineering and technical personnel to a lack of professional training in the design and construction practice along plastic building materials, can not give full play to the technical and economic performance of the wood-plastic building materials.
4. Competition mechanism is not standardized. Quality products appearing on the market inability to sell at the right price, and substandard products have actually cares.
5. Lack of technical and economic policies that support enterprise development, such as: taxes, prices or financial subsidies and other policies.
6. quality supervision and management is not enough, the market is flooded with fake and shoddy products. all about plastic deck boards and sizes

building decoration parts factory production


With the development of society, the advancement of technology, the continuation of the traditional hand-job and on-site processing of the Millennium decoration mode being the challenges of modern civilization and exclusion, its drawbacks become increasingly apparent, such as: poor construction quality, unstable in production serious pollution of the surrounding environment in the process, interfere with the lives of the residents, construction slow the product standards degrees poor. In order to solve these traditional problems, better service to customers, the implementation of building decoration parts factory production is imperative. agriculture wast wood composite
Factory decoration first appeared in the Western countries, about the introduction of domestic 1998. Factory decoration is indoors most of the renovation project through the pipeline operations in the factory production (such as: door, Door, window cover, baseboard, etc.), and then assembled to the scene. Factory decoration with traditional artisanal comparison, has the following advantages:
(1), a guarantee of quality: the use of advanced production equipment of the factory decoration to the production of interior doors, through the production pipeline operations, it is manifested in the following aspects: best non-fading composite decking
A: Standard high finesse: out the door like a door factory production, however, than the door to sophisticated site handmade, produced by the Division I indoor doors with high-end door on the building materials market in quality without any difference.
B: an effective quality assurance: After precision sliding table saw cutting, planing, double diamond drilling slice batch greasy, bottoming, and finally to the spray booth painting, are a series of professional production standards.
(2), and environmental protection: the traditional artisanal construction special paint process, the operation in the field not only quality can not be guaranteed, and will leave a lot of harmful gases in the construction process, they do not get to play. Factory production is all done in the factory, and the current nano-membrane liquid surface treatment technology, can effectively improve the residential and other indoor air quality, and factory production to reduce the workload than on-site operations, but also reduces noise and decoration garbage generated by the on-site operation, so as to reduce the impact on the surrounding environment and the neighborhood. best choice for outdoor decking
(3), shorten the construction period: a lot of work has been transferred to the factory because factory production, while remaining a small part of the work produced by the construction site, so it is more than the traditional artisanal timeliness greatly shorten the construction period. In general, factory production job than traditional construction methods to shorten the time about a month.
(4), material savings: because the mechanical precision and standard factory renovation can be done almost 98% material utilization, which can not be achieved in the case of manual field operations. best composite decking brand

2012年9月17日星期一

basic components of timber board


Great significance to promote the application of factory wood-plastic composite building decoration parts
Wood-plastic composite building decoration parts is less than the outer surface with a hard, dense crusts special hard plant fiber as the main material with PVC resin composite low foam profile and sheet products processing factory production mode environmental protection and energy saving, waterproof, moisture-proof, anti-corrosion, mildew, anti-moth-eaten, no distortion, high mechanical strength, flame retardancy and other characteristics, is an environmentally friendly energy-saving building and furnishing materials. Actual promotion process, you can bring a good economic and social benefits, and has important implications for the creation of a resource-saving and environment-friendly building decoration engineering: basic components of timber board
Promotion and application of wood-plastic composite building decoration parts factory conform to the national development of recycling economy, in line with national energy-saving industrial policy and materials.
Biomass production in the context of our natural resources and the increasing scarcity of oil resources, the use of waste plastic and waste wood composite series production products and processing technology has caused a high degree of attention of the relevant departments of the State. Waste of resources but also resources, plastic products production and life, as economic development is more and more widely, the problem of white pollution caused by plastic waste is handled properly and has become a major environmental problem. The figures show that the plastic waste, municipal waste, has accounted for 25% to 35% of the total garbage. outside decking material
In China, produced annually by the urban population of 2.4 million to 2.8 million tons of waste plastics has become a serious burden of the sanitation department. If you can effective use of waste plastic products will have a significant role in promoting economic development and environmental protection. Timber shortage problem is more and more serious as the economic development. Due to production and the improvement of living standards in the past been used extensively for firewood wood processing waste, such as sawdust, wood shavings, scrap and fiber crops such as straw, rice bran, husk is a serious waste, and the environment The great destructive influence.
According to statistics, China's annual volume of waste wood flour timber processing the remaining millions of tons of other natural fibers such as rice bran production of thousands of tons of these resources, such as the effective development and utilization of considerable value. Waste plastic recycling opportunities in wood-plastic composite material waste plastics and processed waste wood, including sawdust, wood twigs, rice husk, crop straw, peanut shells, add specialty additives, high temperature high pressure treatment made to a certain percentage of structural shapes, are the basis of industrial raw materials. belgium plastic composite deck
It can be directly extruded articles or profiles and then assembled into the decorative parts of building energy efficiency, this new type of wood-plastic composites have good mechanical properties, cheap, easy to process, insect resistance, corrosion, recyclable and features. 98% of the raw materials for wood-plastic composite waste material can be made into a variety of cross-sectional shape and size of the products, and the use and maintenance is simple, can be sawed, planed, nailed, not only retains the advantages of wood processing performance, and to overcome the shortcomings of the wood is not durable afraid infestation.
New bright spot of recycling economy Insiders pointed out that, with the emphasis on the environmental resources improve, to recycling waste materials recycling and comprehensive utilization of resources as the core model of economic development has become the trend of world economic development. Our country is a country with a large population and limited natural resources per capita, far lower than in Western countries. Vigorously develop the resources recycling technology will have a profound impact on national economic development and environmental sustainability. affordable outdoor flooring

According to the the WPC Professional Committee


Can be made of polystyrene foam (EPS), the continuous extruded polystyrene foam (XPS) insulation performance, as technically ripe for energy-saving building materials, mainly used in the construction of walls, roof,places such as windows, doors and ground. EPS, XPS foamed magnification up to 50 times, EPS98% of the volume of air, only 2% of the material, is a fixed air, shock, saving resources, excellent material, with an average load 5 tons per square meter. In addition, microporous plastic with excellent performance, fatigue life increased by 4-7 times 6-7 times higher impact strength than traditional insulation materials, to speed up the process of industrialization will be a major breakthrough in energy efficiency (insulation, thermal insulation) materials. affordable composite/pvc decking
According to the the WPC Professional Committee of CPPIA vice president, chairman of Beijing of Futuresoft Technology Development Co., Ltd., Dr. Song Weining, phenolic foam in recent years developed a new type of material, its flame resistance, low smoke and high temperature stable performance, the adiabatic insulation, sound insulation, easy molding, better durability, and is known as the third generation of emerging insulation materials. In the next few years, phenolic foam, the output value will be the average annual growth rate of 20%.
China is the world's first large windows and doors production and user countries, doors and windows of the demand growth rate of 11% per annum in the doors and windows of the annual new housing demand of more than 500 million m2, while the existing building renovation demand for energy-saving windows and doorsover one billion square meters, Fenestration annual total consumption is equivalent to four times that of Europe. where to buy cheap composite decking
It is understood that the plastic doors and windows, energy efficiency is very prominent, with insulation, sound insulation and moisture characteristics. In the heat transfer, the thermal conductivity of plastics only steel 1/360, 1/1250 of the aluminum, has good insulation properties. At the same time, the plastic doors and windows profiles are multi-chamber structure, make full use of the thermal insulation properties of air, and further reduce the thermal conductivity of the material as a whole. In airtight performance, the plastic door sash feed or fan material between by melt welding, window frames, sashes are a whole, there is no gap between the horizontal and vertical material eliminate the air through the corner of the cross feed and vertical feed stitching possibilities.
According to information available, the plastic profile manufacturing has great advantages in energy saving, from raw materials to produce the whole process of the product point of view, the production of one ton of plastic profile than the production of one ton of aluminum saving 10,000 kwh left and right, and more to produce 1 ton of plastic profile can save 3.6 tons of coal, to reduce the CO2 emissions of 9.43 tons, 30.6 kg to reduce the emission of sulfur dioxide gas, to reduce the emission of nitrogen oxide gases 26.64 kg. backyard patio wpc decking
Wood-plastic composite material is a new type of green building materials, surface appearance, good performance, workmanship, form complex, has a huge market for building materials such as doors and windows, decorative, pinch, template, curtain wall application. Wood plastic aluminum composite windows and doors insulation coefficient over the thermal insulation requirements of the building windows and doors for Beijing, Tianjin, and therefore can play an important role in building energy saving.
The insulation properties of wood-plastic composites significantly better than insulation broken aluminum alloy, avoid aluminum doors and windows difficult to solve indoor condensation leakage problem; whole window wind pressure, water tightness, air tightness performance steel doors and windows, and to avoid the window deformation; weather and useful life than steel doors and windows. In addition, wood surfaces can be processed into solid wood, metal, marble and other effects, decorative aluminum and steel doors and windows. Production of wood-plastic products can be used more than 98% recycled materials, and can be 100% recycled, waterproof, does not rot, anti-moth-eaten, salt, acid, maintenance-free, free paint, formaldehyde and other characteristics, and therefore in the building materials field meteoric rise, promotion and development in China. In his view, energy saving and environmental protection, the development prospects of the wood-plastic composite materials can be expected. backyard patio wpc flower boxes

The plate is a core crust foam new materials


One used to produce PVC WPC crust foam board construction template plastic machinery and equipment, recently put into production in Shanghai Plastic Machinery Manufacturing Co., Ltd.. The equipment energy efficient production of PVC WPC crust foam board construction template applications and broad prospects. affordable composite decking materials
The equipment can be recycled plastic and waste wood chips, sawdust, straw, wheat bran, rice husk plant fibers mixed thoroughly, made ​​of wood-plastic board through a special process and building templates. The plate is a core crust foam new materials, focus on the advantages of wood and plastic, the internal organization of evenly distributed, the surface is flat, smooth, high strength cement used as a building templates affinity, easy to peel. without the use of mold release agents, is the product of choice to replace steel templates and bamboo plastic sheet.
Ka Shi Lau, Secretary-General of the China Resources Association Professional Committee of wood-plastic composites, the Ministry of Energy Saving and Comprehensive Utilization Department Director Mu Ying, South China Agricultural University professor Li Kaifu, Foshan Furniture Industry Association Secretary-General Chu Fook war, total Asia International Furniture Material Trading Centremanager Qianjiang and dozens of wood-plastic business representatives, furniture business representatives attended the meeting. Jia Liu, Secretary-General, presided over the meeting. WPC as a material for the future
  The meeting, Jia Liu, Secretary-General, Qianjiang general trends for wood-plastic composite materials, new materials and furniture applications do a special lecture, detailed wood-plastic composite materials Hong'an the delegation in Senkawa workshop application and its prospects for the development of the furniture market. Wood plastic business representatives and the furniture business representatives to exchange views with each other. The meeting as wood-plastic composite furniture materials market is important to explore.
  It is understood, wood-plastic composite materials are cheap agriculture, forest products and waste the primary biomass fiber material as the base material, the use of the polymer interface chemistry and plastics filled with modified characteristics, physical, chemical and biological engineering special process after the molding process of a reversible multipurpose new materials recycling, the professional name for the synthetic material of the wood bio-fibers and plastics. The use of low-value or waste of resources for the promotion of industrial development is a major feature and advantage of the wood-plastic composite materials.
China has the world's largest construction market, and the unit energy consumption of building area of 2 to 3 times the developed countries, building energy consumption accounts for 27% of the energy consumption of the whole society, wall materials and doors and windows are the main factors affecting the building energy efficiencyone.
Liao, president of the China Plastics Processing Industry Association, said that the potential applications plastic building energy efficiency market in China, not only a large number of on behalf of the steel, and wood, but also has energy-saving materials, ecological protection, improving the living environment to improve the function and quality of construction. reduce building weight, convenient construction superiority. He explained that the Ministry of Housing and Urban building energy efficiency overall objective: to 2010 new construction in cities and towns throughout the country to achieve 50% energy saving. Provide reliable quality, excellent performance of the new plastic wall materials and energy-saving windows and doors for energy-efficient buildings, both the burden shouldered by the plastics industry, but also provides a huge space for the development of the industry. backyard patio composite lumber

Good material for external wall insulation

The Liao, polyurethane (PU) rigid foam is recognized worldwide as the best insulation materials, the construction is simple, cost-effective. Studies have shown that building every 1 kilogram of polyurethane material, equivalent to a decrease of 755 kg of CO2 emissions in the average life of.
It is understood that the PU rigid foams for thermal insulation performance is superior, the lowest thermal conductivity of organic and inorganic insulation materials, and excellent mechanical properties, can withstand a wide temperature range and high-humidity conditions of wind, impact a variety of loads. The material also has a certain toughness, not easy to produce cracking; excellent waterproof, separated steam performance, it is difficult to compare to other insulation materials. PU rigid foam as well as from the carbonization of self-extinguishing characteristics, which can reduce the rate of spread of flame. At present, the building insulation materials in Europe and the United States and other developed countries, about 49% of the polyurethane material, but the proportion in China is still less than 10%. To this end, Liao said, enterprises should actively research and development of low smoke, low toxicity flame retardant green polyurethane foam material, to win market opportunities. backyard patio wood plastic floor

Park Fencing


Replace your worn out fences with our strong, high-quality and maintenance-free livestock fencing systems, netting, barriers or corrals. Whether you are trying to keep deer, foxes, and rabbits out or your livestock, birds, horses or poultry in, we have fencing products to help you. FarmTek's DuraMesh Wire is the perfect wire for livestock, greenhouse benches, anti-bird screen, and poultry cages, while our Poly fencing will keep its attractive appearance while protecting your valuable animals. Keep your dog and pets safe and secure with our K9 fencing and equipment. For work zones, construction sites, hazardous areas, municipalities, factories, warehouses or other businesses, we recommend our barriers and netting for safety, controlling blowing and drifting, as well as to increase visibility. At FarmTek, any fence configuration is possible and most of our fencing and hardware are discounted when purchased in bulk. Park Fencing
During the commissioning of the fence, John Gara, the RDB CEO, said that the park is national asset that must be protected by everybody. He, however, noted that having a population live harmoniously, alongside the animals has not been easy.
"Animals go astray and cause havoc in communities...People lost lives and crops were destroyed. The electric fence offers a solution. People, however, have to be careful with the dangerous fence,' he said.
"The money we gave the affected families will help them to buy seeds, to plant with surety that crops will not be destroyed by animals after the fencing."
Our top of the range Palisade fencing system with brightly coloured UV stable HDPE Palisades bolted to a sturdy fully galvanised steel frame is available in 900 and 1200mm high only. Designed with longevity in mind this virtually maintenance free fencing with a life span of 20+ years is widely used in schools, nurseries and parks.
A tried and tested fencing system over the past 15 Years, with the logs bolted to the framework with no fixings visible at the back it is also a very safe child friendly design. Alpha fencing easily copes with sloping sites. EN Alpha Fencing has the added advantage of no head or neck entrapment when tested. Farm Fence
Commercial and residential customers alike look to AFSCO Fence Supply Company for both sales and installation of quality wood, metal, pvc, and aluminum fencing. Simply stated, a fence is an investment. A professionally installed AFSCO Fence will add value to your property and provide you with security and privacy for many years to come. Homeowners looking for privacy and protection for their children, pets, swimming pools, and tennis courts find one of the largest selections of fence styles in the Capital Region and surrounding areas at AFSCO Fence.
Page wire fencing is a permanent fencing type, available in a wide range of fence heights and horizontal spacing, usually constructed on the farm/field perimeters to control livestock, protect crops and enclose pastures; the nine-strand, 1,200 mm (48 in.) high fence is very popular. The ideal fence height and spacing will depend upon the type of livestock to be excluded. Often a single strand of barbed wire is installed on the posts above the page wire fencing, especially where animals, i.e., horses, tend to reach over the fence. Anchor, corner and stretch posts must be wood, but line posts may be wood and/or steel. Use either a long-lasting wood post such as cedar or a pressure-treated post for maximum life. Post spacings are usually 5 m (16.5 ft). Post lengths will depend upon the choice of page wire fencing height; normally a 2.4 m (8 ft) long post with approximately 1.5 m (5 ft) of post above ground is required to exclude cattle and horses. Page wire fencing is very visible to the animals being excluded. This fencing system is normally more costly to construct than other types, due to higher costs for fencing materials and labour.
Use common sense, don't skimp on materials or cut corners during construction. Allot an adequate amount of time to carefully lay out the fence lines. Confirm property lines to avoid placement errors that could anger neighbors.
When laying out the fence's path, avoid rough terrain, stony areas and steep climbs. Note the property's water sources in pasturing fields, as it may be possible to use a single water source in more than one pasture.
Lanes connect livestock buildings, working facilities and pastures with water. A pasture that ties fields together also could be a passageway.
Lay out the lane so it follows a terrace or natural ridge to prevent gullies. It is best if the lane crosses a well-drained site. If the land is soggy, redirect the livestock and equipment by relocating temporary fencing from time-to-time.
The corner of each field closest to farm buildings is the best place to site lanes. If fields are on opposite sides of a road, place the gates across from each other so animals can go directly across. Use sturdy materials, especially for the hardware & fencing gates, so the animals do not break free or injure themselves and people can easily get in and out. wood plastic composite price

2012年9月16日星期日

exterior flooring products


12 years since the development of wood industry, Nishajuxia the next two years, wood industry in the end what will happen? Environment, make a profit? advantages and disadvantages of composite decking
I believe that after the outbreak of the financial crisis in 2008, in 2009, part of the enterprise first "shuffle" the signs of the market, there is a structural excess, but the last adjustment obviously psychological factors, 80 % to 90% of the doors of businesses still triumph, sales volume and sales has not been a fundamental impact.
But in the second half of 2011, about 70% of the enterprise in storefront retail (non-engineering single), sales of significant decline, and some even a drop of 50 to 60%, which means that a substantial adjustment has begun. I believe that the first half of 2012 to 2013, the wood industry will enter a second adjustment (essentially a wait-and-see period of real estate turnover hovering period excess downturn and door industry capacity stage dictates), but the second the adjusted industry will continue to slightly upward development, mainly due to the following aspects. exterior flooring products
Adjustment of the real estate is the stage. For developing countries, the government is more reluctant to "shooting ourselves in the foot" off the bank's "retreat". The final option is to die so that 20% to 30% of real estate developers. Lower prices and the continued restriction policy, make part of speculators is stuck or convergence to some, but by the end of 2012 or the beginning of next, it is expected there will be an appropriate purchase price "will the lurkers intervention to buy a new one opportunity in the second half of 2013 is expected to generate new categories of procurement "an actual demand (new house occupation period). attractive wpc wpc suppliers
The next two years, the industry profit margins declined slightly, the doors of corporate death 25% is a good thing, this part of the market capacity is just to let other enterprise capacity to fill. Influence of raw materials, labor, rising cost of logistics and industry vicious competition, etc., engineering, interior doors Maori by compression. Tianjin, one of each set of engineering door (some 800 yuan), the gross profit of only about 16%, 5% to 7% of the net profit, slightly do not pay attention to the cost line (not money). Retail interior wood doors profit? Give an example: 6,000 per cubic meter of diverse American red oak, about to do 4 sets of door material (raw material cost per set about $ 1500), plus the production (including paint), marketing costs and profits, finished door ex-factory price of each set to 2300-2500 yuan. The retail price of not more than 4,000 yuan, it is difficult to make money.
National brand wood windows and doors "national standards in the drafting but has not officially come out. Not want to change the interior doors bulk, large-scale production of the status quo, is necessary to achieve the inventory of doors, it is necessary to change the non-standard openings, attributed in the end we should be shaken or change building system (the doorway dimensions reservation building plan). Will be able to complete this process did not happen overnight. Not improve the standard of the industry, generally is premature at the stage of development of the industry, when everything perfect, sound development opportunities are but a small. Data show that the output value of the wood industry in 2011 is expected to 80 billion yuan, but so far, still no one with the quality, service awareness nationwide doors of the brand, and so that people completely acceptable, the doors of quality, service, and there is still a long supporting way to go. In addition, hardware, equipment, accessories enterprises also "Sabre-rattling, but still not well-known brands, such as wooden doors coatings market capacity is probably more than 30 billion yuan. The coatings business confidence is also based on the feudal infighting before a better chance of intervention. back yard decks waterproof woods

Wood-plastic composites (WPC) profile production


Wood-plastic composites (WPC) profile production company Extruwood GmbH, has developed a new PVC-based WPC profile. This product can be used to replace the wooden window frames, aluminum edge banding, in particular, is not strong enough on wooden auxiliary framework. attractive wpc lumber suppliers
Headquartered in Austria Pasching Extruwood company said that in addition to the formation of the protection of the bottom of the wooden frame, Extruwood-Cap profiles insulation effect better than ordinary aluminum sealed wooden frame. In addition, also allows the wood window manufacturers to design slim sash and / or reduce the thickness of the glass.
The company's owner and managing partner of Extruwood SvenWolf retrofitting ordinary aluminum seal window frames with aluminum seal fits well with the thickness of the sash. He said, this will produce hot and cold spots in the heat. To eliminate hot spots and cold spots, the usual practice is to increase the thickness of the wooden sash or embedded in the foam insulation. attractive wpc panels suppliers
Extruwood produced Extruwood-Cap profiles with a direct extrusion process, without using the WPC composite particulate material. Its production line in addition equipped with tapered coaxial rotating twin-screw extruder, with a natural wood fiber drying function.
The company uses the the standard downlink extrusion traction and cutting equipment, the production line has general wood processing functions, such as drainage channels for milling. wpc thermal expansion
The profiles developed products can be used the color WPC, providing products in the form including powder coating, painted or laminated.
Wolf said Extruwood-Cap profile is very cost-effective, it may cause a more conservative and traditional windows buy interest, but also to reduce carbon dioxide emissions. He added that the products are also suitable for window renovation and refurbishment purposes.
Extruwood-Cap solution in October won the the Solvay Innovation Award, Wolf will be held next month in Biarritz, France international wood fiber polymer composites symposium keynote speech. advantage of wood in polymer industry

international wood-plastic composite industry


8-10 November 2011, Battenfeld Cincinnati will participate as a sponsor of international wood-plastic composite industry seminar held in Vienna. By then, it will adapt to the application of the results of today's requirement to reduce the cost of production in this industry innovation wood-plastic composite coextrusion line and a separate set of composite structures: a high-performance "makeshift" live show two. advantage and disadvantages wood plastic composite
Currently, the field of wood-plastic composite face the problem of high cost of production, to this end, manufacturers are seeking solutions. , Wood-plastic composite coextrusion formula cost by reducing the interlayer material can not see, so that 20-25% lower production costs highlight the advantages of one solution - for the outer layer of wood-plastic composite coextrusion coextrusion formulations typically have a higher stabilizer and masterbatch content of, and is designed according to the local market demand and customized, but can not see the intermediate layer material may be used to lower cost formulations. plastic decking boards australia
Based on this, the seminar Battenfeld-Cincinnati, partners Beologic company will demonstrate a high performance wood-plastic composite outdoor flooring extrusion the coextrusion production line demo production line include a fiberEX 92 main extruder, and a Taiwan "space-saving" occupies minimal fiberEX 38 of coextrusion machine. Raw material and production specifications The 160x30mm seven outdoor flooring mold cavity by Beologic and the entire downstream equipment is popular Battenfeld the Cincinnati baseBEX series. attractive wood plastic composite panels suppliers
In addition, Battenfeld Cincinnati will also showcase a wood-plastic composite housing. It is made ​​entirely of wood fiber composite production by the Delta wood products company "makeshift". Such premises equipment especially suitable for temporary shelter or low-cost housing can be quick and easy on-site installation. Delta wood products company can provide thermal insulation, earthquake and hurricane-resistant housing structure, potential customers ranging from aid agencies to the government and the army. attractive wood plastic composite prodcuts suppliers

After deciding on your preferred design


Let's start at the beginning of outdoor shower-style history: the beach cottage with the stall outside around the corner. While its design is a bit more upscale than the typical old-fashioned outdoor stall, it still involves that towel-wrapped dash through the back door into the middle of the house. Sometimes I think that is part of the fun! Outdoor Courtyard Fencing
Commonly described as intimate, intriguing and inviting, front courtyard gardens serve as a transition from the chaos of the streets and world to the serenity of your garden and home. In areas with warm climates, such as California or the Southwest, front courtyards are often used as outdoor living spaces, while in the colonial architecture seen in New Orleans and other areas of the South, formally landscaped entry courtyards are common. But no matter where you live, a well-designed courtyard can add to the curb appeal of your home.
Safety - such as pool fencing must be constructed in accordance with local council by-laws. Pool or safety fencing should be used not only around pools but around any significant risk, (such as cliffs, verandahs, external stairwells etc). The design of safety fencing should take into account these basic principles (in addition to local council requirements). They should be designed so that they are a minimum of 1.2 metres in height with out any horizontal foot holds. Vertical picket closely spaced or solid glass is most commonly used although any design that meets this standard could be used. Horizontal slats can be used as long as the spacing between the slats does not exceed 10mm. Care should be taken around salt water pools to protect steel fittings and surfaces from corrosion.
After deciding on your preferred design, consult your neighbours. Most disputes regarding fences arise from a lack of communication. Information on your rights and obligations can be found under the 'Dividing Fences Act, (NSW, QLD, VIC, ACT)'. Consult the local council regarding the proposed fencing material to check its suitability for the area. For example, Some Councils ban the use of brushwood fencing (for fire reasons), other local councils may have restrictions on height or materials used for front fences and gates. Villa Fencing
The Home Depot offers vinyl fencing in a wide selection of classic and contemporary styles. And because vinyl fencing never needs painting or staining, you'll enjoy maintenance-free beauty for a lifetime.
We provide installation instructions with each order. A lot of assembly information is available here so you can get a sneak preview of the work involved. The hardest part to install vinyl fences is digging in mother earth and mixing the concrete. The vinyl components are light-weight and easy to handle. You could save thousands of dollars installing your own vinyl fence. The skill level required would be comparable to installing a wood fence. If you can use a level and string and have some sense of what looks good, you can install a vinyl fence. Generally, you can dig a hole, assemble a section at a time, and continue to the end of a line. When you have it looking the way you like it, concrete the posts last. This allows you the freedom to raise and lower sections and level posts as you go minimizing the possibility of error. Don't concrete posts until you like what you see.
Solid vinyl Genova Fencing is designed for easy installation. Great-looking from all sides, Genova Fencing brings privacy; shields you from the wind; keeps your pets in, neighborhood pets out. What's more, it is maintenance free and will last a lifetime. Because they are durable vinyl, its parts will never rust, rot, chip or corrode, even in the ground.
Vinyl fence is a fence made using synthetic plastics (PVC, polypropylene, nylon, polythene or from various recycled plastics. If you are looking for fencing for your home, your farm or your horses, then vinyl fencing is an optimal choice. What makes vinyl fence so great is that unlike wooden picket fence or privacy fencing, it is easy to clean and resists weathering.
Our vinyl fence materials used for residential purposes have a reinforced hollow rail design that resembles sawn timber. Because residential vinyl fencing products are usually hollow, they can be too fragile to contain certain horses or livestock, but some designs may be suitable for containing dogs or other pets. Since residential grade rails are made of a thinner material, vinyl horse fence railing or other agricultural fences can consist of a heavy synthetic mold inlaid with cable, synthetic-coated high-tensile wire, or a synthetic coating over a wood or metal rail or plank.
Our vinyl fence products come in many different sizes and colors, integrated during the extrusion process, which means they do not require painting.
We can assist you in your selection and our staff will be there to guide you with placing the order to assistance in installing your fence. Call us today and let us show you why Bufftech Vinyl fencing is so much better than all the other vinyl fence companies on the market. outdoor performance flooring

2012年9月14日星期五

the industry profit margins declined slightly


12 years since the development of wood industry, Nishajuxia the next two years, wood industry in the end what will happen? Environment, make a profit? advanced wpc composite extruder manufacturer
I believe that after the outbreak of the financial crisis in 2008, in 2009, part of the enterprise first "shuffle" the signs of the market, there is a structural excess, but the last adjustment obviously psychological factors, 80 % to 90% of the doors of businesses still triumph, sales volume and sales has not been a fundamental impact.
But in the second half of 2011, about 70% of the enterprise in storefront retail (non-engineering single), sales of significant decline, and some even a drop of 50 to 60%, which means that a substantial adjustment has begun. I believe that the first half of 2012 to 2013, the wood industry will enter a second adjustment (essentially a wait-and-see period of real estate turnover hovering period excess downturn and door industry capacity stage dictates), but the second the adjusted industry will continue to slightly upward development, mainly due to the following aspects. composite wood decking
Adjustment of the real estate is the stage. For developing countries, the government is more reluctant to "shooting ourselves in the foot" off the bank's "retreat". The final option is to die so that 20% to 30% of real estate developers. Lower prices and the continued restriction policy, make part of speculators is stuck or convergence to some, but by the end of 2012 or the beginning of next, it is expected there will be an appropriate purchase price "will the lurkers intervention to buy a new one opportunity in the second half of 2013 is expected to generate new categories of procurement "an actual demand (new house occupation period).
The next two years, the industry profit margins declined slightly, the doors of corporate death 25% is a good thing, this part of the market capacity is just to let other enterprise capacity to fill. Influence of raw materials, labor, rising cost of logistics and industry vicious competition, etc., engineering, interior doors Maori by compression. Tianjin, one of each set of engineering door (some 800 yuan), the gross profit of only about 16%, 5% to 7% of the net profit, slightly do not pay attention to the cost line (not money). Retail interior wood doors profit? Give an example: 6,000 per cubic meter of diverse American red oak, about to do 4 sets of door material (raw material cost per set about $ 1500), plus the production (including paint), marketing costs and profits, finished door ex-factory price of each set to 2300-2500 yuan. The retail price of not more than 4,000 yuan, it is difficult to make money. attractive wood plastic composite fence
National brand wood windows and doors "national standards in the drafting but has not officially come out. Not want to change the interior doors bulk, large-scale production of the status quo, is necessary to achieve the inventory of doors, it is necessary to change the non-standard openings, attributed in the end we should be shaken or change building system (the doorway dimensions reservation building plan). Will be able to complete this process did not happen overnight. Not improve the standard of the industry, generally is premature at the stage of development of the industry, when everything perfect, sound development opportunities are but a small. Data show that the output value of the wood industry in 2011 is expected to 80 billion yuan, but so far, still no one with the quality, service awareness nationwide doors of the brand, and so that people completely acceptable, the doors of quality, service, and there is still a long supporting way to go. attractive wood plastic composite lumber suppliers

attractive wood plastic composite fence


12 years since the development of wood industry, Nishajuxia the next two years, wood industry in the end what will happen? Environment, make a profit? advanced wpc composite extruder manufacturer
I believe that after the outbreak of the financial crisis in 2008, in 2009, part of the enterprise first "shuffle" the signs of the market, there is a structural excess, but the last adjustment obviously psychological factors, 80 % to 90% of the doors of businesses still triumph, sales volume and sales has not been a fundamental impact.
But in the second half of 2011, about 70% of the enterprise in storefront retail (non-engineering single), sales of significant decline, and some even a drop of 50 to 60%, which means that a substantial adjustment has begun. I believe that the first half of 2012 to 2013, the wood industry will enter a second adjustment (essentially a wait-and-see period of real estate turnover hovering period excess downturn and door industry capacity stage dictates), but the second the adjusted industry will continue to slightly upward development, mainly due to the following aspects. composite wood decking
Adjustment of the real estate is the stage. For developing countries, the government is more reluctant to "shooting ourselves in the foot" off the bank's "retreat". The final option is to die so that 20% to 30% of real estate developers. Lower prices and the continued restriction policy, make part of speculators is stuck or convergence to some, but by the end of 2012 or the beginning of next, it is expected there will be an appropriate purchase price "will the lurkers intervention to buy a new one opportunity in the second half of 2013 is expected to generate new categories of procurement "an actual demand (new house occupation period).
The next two years, the industry profit margins declined slightly, the doors of corporate death 25% is a good thing, this part of the market capacity is just to let other enterprise capacity to fill. Influence of raw materials, labor, rising cost of logistics and industry vicious competition, etc., engineering, interior doors Maori by compression. Tianjin, one of each set of engineering door (some 800 yuan), the gross profit of only about 16%, 5% to 7% of the net profit, slightly do not pay attention to the cost line (not money). Retail interior wood doors profit? Give an example: 6,000 per cubic meter of diverse American red oak, about to do 4 sets of door material (raw material cost per set about $ 1500), plus the production (including paint), marketing costs and profits, finished door ex-factory price of each set to 2300-2500 yuan. The retail price of not more than 4,000 yuan, it is difficult to make money. attractive wood plastic composite fence
National brand wood windows and doors "national standards in the drafting but has not officially come out. Not want to change the interior doors bulk, large-scale production of the status quo, is necessary to achieve the inventory of doors, it is necessary to change the non-standard openings, attributed in the end we should be shaken or change building system (the doorway dimensions reservation building plan). Will be able to complete this process did not happen overnight. Not improve the standard of the industry, generally is premature at the stage of development of the industry, when everything perfect, sound development opportunities are but a small. Data show that the output value of the wood industry in 2011 is expected to 80 billion yuan, but so far, still no one with the quality, service awareness nationwide doors of the brand, and so that people completely acceptable, the doors of quality, service, and there is still a long supporting way to go. attractive wood plastic composite lumber suppliers

Wire fences rely on braced


At Penrod Lumber and Fence Company, we have a long-standing tradition of building quality horse fencing. We specialize in 4-Board Farm and Ranch fence construction. These types of fences add a great look to any property. Over the last two decades, our crews have built miles of fence all across the continental US stretching from northeast to the southern tip of Florida and the west coast. Our company has grown to include a large fleet of trucks and a network of fence crews that build quality, custom fences with our advanced installation techniques in every area of the country. Horse farm Fence
Steel wire continues to be among the most economical materials from which to construct fences. Smooth steel wire is most often used to manufacture barbed wire or woven wire fence.
Wire fences rely on braced end posts and line posts installed between them to support the wire. Posts can be made of wood, steel, plastic or fiberglass. Typical installations include braced 7- to 8-inch-diameter wood end posts with steel T-posts in between. Steel posts are easy to drive by hand, while wood posts generally require you to dig post holes and tamp soil around each post.
Low-tensile (conventional) steel wire with a low carbon content is still used to construct most wire fences. This material bends and stretches easily, but is relatively inelastic — so if it stretches, it doesn't contract back to its original state. These characteristics mean that it's easy to work with, but also subject to sagging and breakage. Conventional wire requires more line posts spaced closer together for support than high-tensile wire. Park Fencing
High-tensile wire is more difficult to work with, but fences made of it stay tighter longer because the wire is stronger and more elastic. Working with high-tensile wire also requires greater care with setting end posts and braces due to the additional tension they must bear. While the high-tensile wire itself may cost more than its conventional counterpart, you can choose a lighter gauge high-tensile wire and get the same or greater strength than you would with conventional. High-tensile wire fences require fewer line posts, which saves money and labor overall.
The easy fit park fencing uprights, posts and gates come already finished. The top rail and the four lower rails can be primed or galvanised, ready for painting once they are in place. *Please note: When ordering, please state if you would like your estate fencing primed or galvanised. If you are unsure, take a look at our finishes page for more details on the processes, or contact our team at W. Stay & Son.
Our traditional metal deer park fencing is ideal for use as a continuous boundary fence in parkland, deer parks or estate grounds. The fencing is constructed from round & flat steel bar. It is supplied with a hot dip galvanised finish. Ideal for use on uneven ground, it can follow the contours of the ground and can be easily curved.
Deer park fencing can be fabricated either in panels or continuous railings. The external height is normally 1.8 to 2 metres with approximately 550mm below ground.
Back support bars can be supplied if required, alternatively, we recommend a 100 x 100mm post at regular intervals. Where welded panels are to be used for deer park fencing, these would come in a maximum of 2 metre lengths due to the handling weight. We can match to any existing or old style fencing; however in certain cases the cast iron can prove to be very expensive. We always ensure the correct methods and materials are provided at the most reasonable of prices.
We can also install the estate fencing and gates for you - our team have over 30 years experience. Fitting service available in most parts of the country. No site welding - constructed using the traditional method. CDI also make and supply wrought iron tree guards, bridges, driveway entrance gates and bespoke metalwork for gardens and parks. wpc panel decking

2012年9月13日星期四

attractive outdoor wood plastic wall


Has begun it comes to wood-plastic material applications including dado, windowsill, sets of doors, floor, corridor, cut off the roof, parapets, edging, fence, bridge, bathroom, door and window sets, rest kiosks, garage, deck of the ship, furniture accessories, water channels, outdoor seating, stair treads, open-air platform, container decking, playground seat, light rail soundproof walls, multi-function wall partition, highway noise walls and began to penetrate the building, home improvement, logistics, packaging gardens, municipal, and environmental protection industries, the annual gross domestic product is increased every year, the market prospect is very broad. Therefore, I believe: wood-plastic composite materials industry in China has been to the development of a new round of the "critical point". attractive outdoor wood plastic wall
With the advantages of wood-plastic materials gradually been excavated, and the research work of the project in 2002 was included in the Chinese Academy of Sciences, "High Technology Development Report 2002"; 2003, the National Development and Reform Commission will be included in the "national high-tech industry of new wood-plastic composites aspects of material special projects "; June 2005, the State Council issued the recent focus on the work of building a conservation-oriented society.", the "notice" preferential tax policies to improve the comprehensive utilization of resources and the recycling of waste materials a series of specific guidance. attractive wood plastic composite decking manufacturers

"Turning waste into treasure" to create a "win-win"

According to the country's economic policy orientation, the wood-plastic composite materials and their products will be the next few years, the national focus on the development of new materials. WPC TECHNOLOGY CO. to Shantou Xinyuan development of wood-plastic products industry is the most comprehensive, Guangzhou Ocean Technology Development Rich the Bulgari excellent solid wood floor test sample has also been approached or reached the international advanced level. In addition, many companies in the South are increasingly prominent features of their own products. redwood composite decking prices
The WPC industry as a multi-faceted, large span, specialization, and the edge of the emerging industry, its equipment, technologies and processes involved in the precision machinery, fine chemicals, hydraulic transmission, vacuum technology, heat conduction, fluid mechanics, sensor technology, electronic automatic control and computer programming. Guangzhou Fu Bulgari floor is a self-developed patented products by the modern high-tech enterprises - Guangyang its production of solid wood flooring with exclusive new green floor covering material. adhesive for wood plastic composite or wpc

plastic composite decking boards


The wood-plastic composite material is a plastic and wood fibers to add a small amount of chemical additives and fillers mixed through dedicated with processing equipment made ​​of a composite material. Durable, long life, have the appearance of wood than plastic products, high hardness, good rigidity, secondary wood processing: sawing, planing, bonding, fixed with nails or screws, and easy maintenance; texture can be manufactured according to the needs of a different color, aging resistance and long service life, the material of choice for outdoor decoration garden, landscape design, patio, flooring, landscape chairs, fence making. additives for wpc, wood grain texture
China's wood-plastic composite materials research and development began in the 1990s, a decade later than abroad. Since the late 1990s, with the wood packing material from China, the United States took the lead limit, research and development of China's wood-plastic materials, its technology into entering a period of rapid development. The beginning of the century, had become the prototype of the WPC industry in China.
At present, the domestic research and development of wood-plastic material structure class, several major types of decorative class wrapper classes and special classes, including wire, profiles, plates and profiles, and other series, and its scope is almost covered by logs, plastic, use of steel, aluminum and other similar composite fields. plastic composite decking boards

By policy Dongfeng, the rise of the wood-plastic heat

Wood plastic, also called eco-wood, mainly waste plastic and twigs, tree branches, rice husks, agricultural straw and other plant fiber as raw material products, widely used for packaging, gardening, transportation, construction, home improvement, travel, interior and so on. Dual advantages of its blend of "wood" and "plastic", with environmental protection, waterproof, corrosion-resistant, pest control, fire-retardant, recyclable and so many advantages, is a highly promising low-carbon, green loop "material. Wood-plastic products according to their commonly used raw materials can be divided into two categories of PVC and PE with diverse colors, bright colors, complete specifications, different shapes, plasticity, and a strong sense of wood texture for interior, more unique decorative properties. attractive outdoor wood plastic composite floor
Wood-plastic composite materials are a class of basic materials covering a wide variety of products, diverse morphology, it fully reflects the circular economy, resource utilization, environmental health, saving alternative advanced concepts for the sustainable development of the economy. Most of its products have the comprehensive utilization of resources, protection of the environment and the resulting function, so in recent years gradually attracted the attention of the community. Currently, our government circular economy and build a conservation-oriented society "concept proposed to add a powerful impetus to the development of China's WPC industry. attractive outdoor wood plastic composite material

Football field fence


The Archerfield golf course development outside Dirleton in East Lothian was the scene of the first test cast of the access legislation. Although the case was eventually settled out of court, East Lothian Council was successful in getting the developer to comply with the legal notice they had served almost a year earlier. Golf course fencing
This 500-acre estate includes two golf courses and 100 plots for luxury housing. Unfortunately, the anti-access developer effectively banned any member of the public from the site by removing a bridge over a burn, putting a barbed wire fence along one side of the estate where there is a strip of woodland, and erecting intimidatory signs warning of prosecution if people enter the "construction site", where golfers could be seen playing a round. It seemed that his aim was to create an exclusive gated community in East Lothian.
Ramblers Scotland worked with Dirleton residents to urge East Lothian council to take action to uphold access rights. After a legal notice was served in September 2005 under Section 14 of the Land Reform Act, the developer lodged an appeal, and the preliminary hearing of the case was held at Haddington Sheriff's court on 28th November.
A further hearing on 23-24th March 2006 took the form of a legal debate to argue the relevancy, competency and specification of the notice. The Sheriff was unable to come to a ruling based on these arguments, so a further hearing to listen to the evidence of witnesses was called, and was due to run from 14-25th August.
Fencing for sports grounds and sports areas such as Golf Courses, Tennis Courts, Ball Courts, Football Pitches, Basket Ball Courts, Football Grounds etc, all require different types of fencing materials. The detailed specification of the fencing will depend on quite a few different factors such as the type of sports played and the security issues.
At Charleton fencing our sports ground fencing comes in many different styles and patterns to suit your requirements. We have a team of people that are all experienced in delivering the right product to suit your requirements.
On 7th August 2006, a week before the case came to court, the council announced that negotiations between them and the developers had led to a settlement being reached between the parties. The barbed wire fence had been removed, notices changed, and the bridge over the burn was to be rebuilt. A number of other points were also agreed, including the construction of paths on the estate, including one down the Common Strip. Football field fence
We are pleased that this case has been resolved, but at the same time will continue to monitor the situation at Archerfield to ensure that the developer enables access rights to be exercised over all land on which they apply, and that no further obstructions are put in place.
Restrict access and protect your football field with sports field fencing and access gates. Our professional crews are skilled craftsmen trained to deliver superior sports fencing installations. Our experienced operations staff is devoted to prompt and reliable service.
Spray and Clean Composite Deck Cleaner cleans spots and stains from within the composite decking. Do you have a composite deck that has black stains and spotting that you can not get cleaned. Have you tried just about every possible deck cleaner but just cant seem to get the deck any cleaner? That's because the stains are within the decking, where you would think it would be impossible to clean but that's not the case.
Typical composite deck cleaners, clean topically and may work well on surfaces but are ineffective at internal stains. This internal staining became a huge problem for composite decking manufacturers because composite decking was supposed to be "maintenance free". The Trex company had a class action lawsuit filed against them for using the words "maintenance free" in their marketing. Spray and Clean is the only composite deck cleaner capable of cleaning in this fashion. To formulate this product we had to use chlorine bleach but only 5%, the chlorine is transported into the composite decking by a special formula of chemicals where it can remove the stains without scrubbing or rinsing. black composite decking

2012年9月12日星期三

main component in the processing of thermoplastic


Plastic enhancements, in addition to other than the traditional glass, aramid fibers and carbon fibers, natural fibers are being more and more applications. In many cases, the wood fibers and the sawdust filled plastic can be a good substitute for natural wood or medium density fiberboard, they can also be opened up to a broader market. Wood fibers and thermoplastic be utilized together to produce a wide variety of extrusion products. The proportion of the wood can be as high as 90%. acrylic impregnated wood flooring basement
Celecoxib are additives, this main component in the processing of thermoplastic polymers, wood and other natural fibers, compared with the inorganic filler and the reinforcing fibers, has many advantages. They are lighter, less likely adhesive material is updatable. For example, wood chips can be used as a filler to reduce the cost of materials, but it can also be used to improve the strength or the dimensional stability of the temperature independent. The negative aspect is an increase in weight.
The combination of wood and thermoplastics is not a new thing, but to rely on the new technology, the wood has a simple additive, developed to assume from the principal component of the role, a new performance and possibilities. Wood extrusion in the United States has been using for decades, but did not win a large market scale compared with the plastic extrusion and full wood working. The early 1980s, to the interior parts of the automotive industry, commercial applications, and since then continuous development. For the first time an international wood-plastic composite materials seminar held in 1991 in the United States Madison. From 1990 to 2000, the U.S. market growth of about 135%, especially in the last five years significant. new outdoor deck production
Europeans filled thermoplastic extruded wood fiber can be traced back to 1977. However at the time timber content is only 30%. In the process of time, this proportion has been rising sharply. The term "liquid wood" is sometimes used incorrectly molded timber. The liquid timber is used to describe the use of lignin as a basic ingredient material. Lignin and natural fibers are mixed together and heated to produce the fiber composite material can withstand further processing.
The wood facing new competitive wood extrusion effectively combine the advantages of the two materials. Get an synergies between the various economic processing methods used in the positive performance of the wood and plastic technology. However, it must take into account the performance of the wood fiber material profiles can not be compared with the performance of the polypropylene (PP), polyethylene (PE) or polyvinylchloride (PVC) material. In other words, the window frame profiles with the prominence of PVC, wood fiber material will not change anything. The wood extrusion positioning market have so far been involved in traditional materials such as wood or medium density fiberboard. attractive composite prodcuts suppliers
Granulation testing machine and extrusion testing machine is a small experimental simulation workshop production equipment and technology equipment. Before the introduction of the sets of laboratory equipment and technicians to develop new products in the production line sample. Experiment not only test quantity production equipment using large experimental energy consumption and the impact of the workshop to normal production experiment less efficient, long life cycle experiment, serious impact on the progress of the product development. The inputs of the equipment greatly reduces the cost of experiments, greatly reducing the experimental period, and injected fresh blood into the research and development of new products, enhanced R & D capabilities of the technical department, and further accelerate the process of new product development. attractive outdoor composite panels

London Olympics figure also campaign


In June 2011, when the first batch of 50 tons of recyclable wood plastic version is loaded into the container towards the London Olympic Games venues direction Huanhuandecong Anhui, which means Michael Phelps, Liu Xiang, Bolt sportslarge coffee on production from Anhui, lounge chair and shower board "will be used during the Olympic Games in London. attractive composite material suppliers
When a reporter to interview the manufacturer of the product, Anhui Qizhen WPC Technology Co., Ltd. Chief Engineer FANG Xiao Zhong, he still contain his share of proud. "As early as before the Olympic Games in London, the company's products will cut a striking figure in the Beijing Olympic Games, Shanghai World Expo and other domestic sporting event, this time through the joint efforts of the executives and staff, left outside sporting event London Olympics figure also campaign for the company overseas markets to enhance a high bench. "
"Very unexpected, settled in London Olympics outset smoothly." FANG Xiao Zhong said, for a world-class event venues, stationed in the product must have absolute product quality and performance guarantees, on a company's strength and level of extremely exacting requirements. So early stage company with a long time to do the investigation, study samples. In June 2010, the company received the London Olympic Games venue construction committee letter reply, LOCOG a strong interest in the company's wood-plastic composite products. advanced wpc composite extruder manufacturer
"From the start in mid-May 2011, the company gradually lounge chair for the Olympic venues, locker room benches, shower panels and other products, back and forth doing, the company has a total of 380 tons of recycled wood-plastic board, worth about more than 300 million this order, but the quality of products must be to ensure that. "FANG Xiao Zhong, success in the London Olympics through the Qizhen wood plastic platform to display to the world's most powerful and persuasive, fired a of Anhui brand building materials industries in the world brand reputation.
Wang Ke Xia, Anhui Academy of Social Sciences Institute of Industrial Economics, said in an interview with reporters, after China's accession to the WTO, the Chinese-made knock on the door of the world, China's economic integration with the world economy gradually. This time the "Anhui elements can come to the fore, and representative of what" Anhui "enhance the quality, also marks Anhui enterprises in international competition with high-end wave driven, been introduced into the high-end market. acrylic impregnated engineered flooring
Previously, the globalization of Anhui seems a long way off, but with the constant development in recent years, Anhui, especially with the Little City with a building industries to relocate to the pace continues to accelerate, a series of significant opportunities in front of the national technology innovation project pilot provinces slowly by the initial stage of the industry of the province to enter the high-end and depth. "So whether it is in China, the Chinese creation, Anhui elements settled in London Olympics, are more or less there is necessarily linked." Wang Ke Xia think so.
Anhui enterprises in the future on how to better tap the sporting event this cake, in king may Xia opinion, first of all, you should encourage enterprises entailed opening up overseas markets, followed should strengthen brand building, out of the high consumption, high pollution and low-cost export situation allow the market to have a sense of identity. attractive composite decking suppliers